Calculator

Mulch calculator

This turns area and depth into cubic feet and cubic yards, and into bags only when you enter a bag size.

How to measure your area

Use a tape or a wheel. Measure at the ground.

Round each side up to the nearest half foot. Measure the depth you actually want.

For a large or irregular bed, split it into rectangles, triangles, trapezoids, circles, and quarter circles. Measure each piece, run it here, and add the results. You can add more than one area on this page.

Do not overlap the pieces or count the same ground twice. Sketch them and label each one. Use the same depth on every piece. If you add an extra percent, add it once at the end.

Units

Printed on the estimate. Stored only in this page.

Areas

Zero length or width is allowed and adds nothing. A negative or a blank is an error. Depth must be greater than zero.

Bed shapes and mulch depth A rectangular bed and a circular bed, plus a side view of mulch depth on the soil. The circle is measured by its diameter, the distance across through the center. length width diameter depth Rectangle Circle mulch soil Side view
A rectangular bed and a circular bed, plus a side view of mulch depth on the soil.
ft
ft

Typical planning range on this tool is 1 to 6 inches. Outside that, you get a note and the volume still runs.

in
10 ft length10 ftDepth 3 in
Your bed, in plan. The labels are the numbers you type.

Leave blank to show volume only. Check the bag you actually buy.

cu ft

Starts at 0. No settle rate is assumed.

%
Optional prices you type

Example result. Example 1.

You’ll need 25 cubic feet (0.926 cubic yards) of mulch for this area.

Shopping list

Want a more detailed estimate? Fill in the optional prices above.

Front bed

  • 25 cubic feet (0.926 cubic yards) Bed volume

    Area times depth, before any extra percent.

  • — Bags

    No bag size entered, so no bag count.

No prices entered. This page does not invent a market price.

Assumptions for this estimate
  • Volume is area times depth. Rectangle area is length times width. Circle area is π times radius squared, using JavaScript’s Math.PI.
  • Triangle area is one half times base times height. Trapezoid area is the average of the two parallel sides times the height between them. Quarter-circle area is π times radius squared, divided by 4, using JavaScript’s Math.PI. Those areas then use the same depth, waste, and rounding.
  • Depth is converted with 12 inches per foot. Cubic yards are cubic feet divided by 27.
  • Displayed cubic yards are rounded half away from zero to 3 decimal places. Bag math uses the full volume, not the rounded display.
  • Bag size is blank, so no bag count is shown. The tool does not assume a bag.
  • Waste is 0%. The default for a new mulch estimate is 0 because this tool does not assume a settle rate.
  • A depth under 1 inch or over 6 inches still calculates. Horticultural guidance for trees and shrubs is often about 2 to 4 inches; see the methodology page.
  • Zero area returns zero volume.

What to buy next

  • Order the cubic yards if you are buying bulk, or the bag count if you entered a bag size.
  • Read the bag: a “2 cubic foot” label is the size to type, not a coverage slogan.
  • No product and no price is recommended here.

Formula

Rectangle area = length × width. Circle area = π × radius². Volume in cubic feet = area in square feet × depth in inches ÷ 12. Cubic yards = cubic feet ÷ 27. Several beds are added. Waste, if you set it, is applied once to that volume before the bag split. Bags = order volume ÷ bag size, rounded up.

Triangle area = 1/2 × base × height. Trapezoid area = (a + b) / 2 × height, where a and b are the two parallel sides. Quarter circle area = π × radius² / 4. Those areas use the same volume, rounding, and bag count.

A 10 ft × 10 ft bed at 3 in is 25 cubic feet, shown as 0.926 cubic yards. Last reviewed 8 November 2026. Sources and rounding.

When this formula is wrong

  • The bed is not a rectangle, circle, triangle, trapezoid, or quarter circle, or the depth changes across it.
  • Plants, edging, and fabric steal area you did not subtract.
  • Fresh mulch settles and decomposes. The extra percent starts at 0 because no single settle rate is used.
  • A bag’s coverage chart assumes the depth printed on the bag, which may not be yours.
  • Bulk yards may have a delivery minimum this tool does not know.

Worked examples

These three use the same functions as the form. Load them with the buttons on the calculator.

  1. 1. The 10 by 10 foot check

    A 10 ft by 10 ft rectangle at 3 inches deep, and no bag size. Volume only.

    Inputs

    • Bed 1: 10 ft × 10 ft × 3 in
    • Waste: 0%
    • Bag size: blank

    Intermediates

    • Area: 100 sq ft
    • Bed volume: 25 cu ft
    • Order volume: 25 cu ft
    • Bags: not calculated

    Result. You’ll need 25 cubic feet (0.926 cubic yards) of mulch for this area.

  2. 2. Bags, with waste once

    A 20 ft by 4 ft bed at 3 inches, 10% waste, and 2 cubic foot bags.

    Inputs

    • Bed 1: 20 ft × 4 ft × 3 in
    • Waste: 10%
    • Bag size: 2 cu ft

    Intermediates

    • Area: 80 sq ft
    • Bed volume: 20 cu ft
    • Order volume: 22 cu ft
    • Bags: 11

    Result. The beds are 20 cubic feet (0.741 cubic yards) before the extra percent. With 10% added once, order 22 cubic feet (0.815 cubic yards), which is 11 bags of the size you entered.

  3. 3. Two beds added together

    An 8 ft by 3 ft strip plus a 4 ft diameter circle, both 2 inches deep.

    Inputs

    • Bed 1: 8 ft × 3 ft × 2 in
    • Bed 2: 4 ft diameter × 2 in
    • Waste: 0%
    • Bag size: blank

    Intermediates

    • Area: 36.566 sq ft
    • Bed volume: 6.0944 cu ft
    • Order volume: 6.0944 cu ft
    • Bags: not calculated

    Result. You’ll need 6.09 cubic feet (0.226 cubic yards) of mulch for this area.

Questions

Why is there no bag count until I enter a bag size?

Bag labels differ. Leaving the bag size blank shows cubic feet and cubic yards only. The tool will not invent a bag.

Does this include settling?

Not unless you type a waste percent. Fresh mulch settles and breaks down, and there is no single percent in the sources used here. The field starts at 0.

What if the bed is not a rectangle?

Use a circle, triangle, trapezoid, or quarter circle, or add several of those shapes. The volumes are added. A kidney shape, a slope, or a depth that changes across one bed is outside the formula.

Is 3 inches the right depth?

Three inches is inside the 2 to 4 inch range described by University of Illinois Extension and Penn State Extension for many tree and shrub beds. It is not a prescription for your soil. Depths under 1 inch or over 6 inches still calculate, with a warning.

Why might the bag’s coverage chart disagree?

Coverage charts assume their own depth. This page uses your depth: cubic feet = area in square feet × depth in inches ÷ 12. Compare that with the chart instead of replacing the math.

Methodology

Last reviewed 8 November 2026. Depths under 1 inch or over 6 inches still calculate. University of Illinois Extension and Penn State Extension describe about 2 to 4 inches for many tree and shrub beds. That is guidance, not a setting this tool forces. See the citations.