Calculator

Gravel calculator

This turns area and depth into cubic yards, then into pounds and short tons at the density shown next to the weight.

How to measure your area

Use a tape or a wheel. Measure at the ground.

Round each side up to the nearest half foot. Measure the depth you actually want.

For a large or irregular bed, split it into rectangles, triangles, trapezoids, circles, and quarter circles. Measure each piece, run it here, and add the results. You can add more than one area on this page.

Do not overlap the pieces or count the same ground twice. Sketch them and label each one. Use the same depth on every piece. If you add an extra percent, add it once at the end.

Units

Printed on the estimate. Stored only in this page.

Areas

Zero length or width is allowed and adds nothing. A negative or a blank is an error. Depth must be greater than zero.

ft
ft

Typical planning range on this tool is 1 to 6 inches. Outside that, you get a note and the volume still runs.

in
10 ft length10 ftDepth 3 in
Your bed, in plan. The labels are the numbers you type.
Density

Presets are cited averages. Your supplier’s number wins. Weight is never shown without the density name.

From volume to weight Area and depth make volume. Density turns that volume into weight. Compaction is added only if you enter an extra percent. area depth area × depth = volume + extra percent, if you enter one × density weight
Area and depth make volume. Density turns that volume into weight. Compaction is added only if you enter an extra percent.

FHWA Federal Lands Highway PDDM earthwork exhibit, loose mass density: dry uniformly graded gravel, 2,700 lb/yd³. Divided by 27 that is 100 lb/ft³. This is not FHWA-HRT-15-034 Table 7, and it is not a density for every gravel. Footnotes on that exhibit say the figures vary.

lb/ft³

Using: FHWA Federal Lands: loose, dry, uniformly graded gravel

Starts at 0. Compaction is not included until you set this.

%
Optional prices you type

Example result. Example 1.

You’ll need 25 cubic feet (0.926 cubic yards) of gravel, about 2,500 pounds (1.25 short tons, 2,000 lb each) at 100 lb/ft³ — FHWA Federal Lands: loose, dry, uniformly graded gravel.

Shopping list

Want a more detailed estimate? Fill in the optional prices above.

Path

  • 25 cubic feet (0.926 cubic yards) Bed volume

    Area times depth, before any extra percent.

  • 25 cubic feet (0.926 cubic yards) Order volume

    Same as the bed volume because the extra percent is 0.

  • 1.25 short tons Weight

    2,500 pounds from the bed volume at 100 lb/ft³ (FHWA Federal Lands: loose, dry, uniformly graded gravel). No extra percent was added.

  • 1.25 short tons Order quantity

    No sales step, so this is not rounded up.

No prices entered. This page does not invent a market price.

Notes

  • Weight uses 100 lb/ft³ (FHWA Federal Lands: loose, dry, uniformly graded gravel). Moisture, gradation, and the supplier’s ticket change the real weight. Do not treat this preset as the load on the truck.
Assumptions for this estimate
  • Geometric volume is area times depth, same as the mulch tool. Waste or compaction percent, if you set one, is applied once to that volume before weight.
  • The default extra percent is 0. Compaction is not included until you enter it.
  • Weight is order volume times 100 lb/ft³ (FHWA Federal Lands: loose, dry, uniformly graded gravel).
  • Short tons are pounds divided by 2,000. Metric tonnes are pounds times 0.45359237 kg, divided by 1,000. Those are different units.
  • The extra percent is separate from the density. It starts at 0. Choosing a chart average does not add compaction, and choosing the Federal Lands 100 lb/ft³ figure does not mean the gravel is FHWA No. 57.
  • No sales step is set, so the order quantity is the calculated short tons and is not rounded up.
  • Displayed pounds may be rounded to the nearest pound. The ton math uses the unrounded product.
  • Preset densities are published planning averages cited on the methodology page. They are not a live supplier price or a lab test of your pile.

What to buy next

  • Ask whether the yard sells by the short ton or the cubic yard, and use that line.
  • The estimate names the density. It does not claim the truck will match it.
  • It does not name a quarry or a price.

Formula

Volume matches the mulch calculator: area × depth, with 12 inches per foot and 27 cubic feet per cubic yard. A triangle is 1/2 × base × height, a trapezoid is (a + b) / 2 × height, and a quarter circle is π × radius² / 4. Weight in pounds = order volume in cubic feet × density in lb/ft³. Short tons = pounds ÷ 2,000. If you set a sales step, the order quantity rounds up to that step. An exact step stays put.

The starting density is 100 lb/ft³ from the FHWA Federal Lands table for loose, dry, uniformly graded gravel (2,700 lb/yd³ ÷ 27). That is not the FHWA-HRT-15-034 No. 57 laboratory range, and it is not every gravel. Last reviewed 8 November 2026. Sources and the other presets.

When this formula is wrong

  • The supplier’s ticket, the moisture, or the gradation does not match the preset. Use their number.
  • You need the compacted depth after rolling. The extra percent starts at 0, so compaction is absent until you type it.
  • A driveway or parking pad needs a section designed for soil and load. Choosing “vehicle area” only adds a warning.
  • Base and surface are different materials. Enter one bed per layer.
  • A compacted measurement factor, such as Ohio DOT Item 411 at 3,800 lb/yd³ for crushed stone, is not an order weight.

Worked examples

These three use the same functions as the form. Load them with the buttons on the calculator.

  1. 1. Known volume at the FHWA loose density

    The same 10 ft by 10 ft by 3 in volume as the mulch check, at 100 lb/ft³.

    Inputs

    • Bed: see situation
    • Density: 100 lb/ft³
    • Placement: path
    • Order step: none

    Intermediates

    • Volume: 25 cu ft
    • Displayed cubic yards: 0.926
    • Pounds: 2500
    • Short tons: 1.25
    • Order quantity: 1.25 short tons

    Result. You’ll need 25 cubic feet (0.926 cubic yards) of gravel, about 2,500 pounds (1.25 short tons, 2,000 lb each) at 100 lb/ft³ — FHWA Federal Lands: loose, dry, uniformly graded gravel.

  2. 2. Same volume, different preset

    Nothing changes except the density preset. Volume stays put. Weight moves.

    Inputs

    • Bed: see situation
    • Density: 103 lb/ft³
    • Placement: path
    • Order step: none

    Intermediates

    • Volume: 25 cu ft
    • Displayed cubic yards: 0.926
    • Pounds: 2575
    • Short tons: 1.2875
    • Order quantity: 1.288 short tons

    Result. You’ll need 25 cubic feet (0.926 cubic yards) of gravel, about 2,575 pounds (1.288 short tons, 2,000 lb each) at 103 lb/ft³ — DelDOT chart average: #57 stone.

  3. 3. A vehicle pad, ordered in 0.1 ton steps

    A 10 ft by 20 ft by 4 in vehicle area. The warning stays editorial. The order quantity rounds up to 0.1 short ton.

    Inputs

    • Bed: see situation
    • Density: 100 lb/ft³
    • Placement: vehicle
    • Order step: 0.1 short ton

    Intermediates

    • Volume: 66.6667 cu ft
    • Displayed cubic yards: 2.469
    • Pounds: 6666.6667
    • Short tons: 3.3333
    • Order quantity: 3.4 short tons

    Result. You’ll need 66.67 cubic feet (2.469 cubic yards) of gravel, about 6,667 pounds (3.333 short tons, 2,000 lb each) at 100 lb/ft³ — FHWA Federal Lands: loose, dry, uniformly graded gravel.

Questions

Why does the weight change when I switch presets but the volume does not?

Volume comes from area and depth. Weight is that volume times the density you select. The 100 lb/ft³ preset is only the FHWA Federal Lands loose dry uniform-gravel figure. The DelDOT #57 chart average is 103 lb/ft³. Switching presets changes the weight and leaves the volume put.

Which density should I pick?

Use your supplier’s figure when you have it. The presets are a federal loose-gravel estimate and two Delaware DOT averages, cited on the methodology page. They are not your ticket. Moisture and gradation move the weight.

Does this include a compacted base for a driveway?

No. Choose “vehicle area” and you still only get the volume of the depth you typed, plus a warning. Compaction is included only as an extra percent you enter. The default is 0. A compacted measurement factor, such as Ohio DOT’s 3,800 lb/yd³ for crushed stone in Item 411, is a different kind of number and is not used as an order weight.

Should I order cubic yards or short tons?

Ask the yard which unit they sell. Both are on the estimate. Short tons always mean pounds ÷ 2,000, and the density used is printed next to them. If you set a sales step, the order quantity rounds up so the step does not under-buy.

Is this an engineering design?

No. It does not design a pavement section, check soil, or apply a local standard. It converts the area and depth you already chose into volume and weight.

Methodology

Last reviewed 8 November 2026. Presets name the publication, the material, and the condition: Federal Lands loose dry uniform gravel at 100 lb/ft³; FHWA-HRT-15-034 Table 7 No. 57 minimum 95.4 and maximum 108.7; DelDOT chart averages 98 and 103, which are not labeled loose or compacted. A custom density replaces all of them. Read the citations.